Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Shake or scrape for percussion sounds
Two instruments in one: fill it with rice or lentils and close the lid to shake it, or scrape a pencil along the ribbed sides for a guiro rasp.
Printing notes
23.5 cm³
Volume
29.1 g
Est. weight
11,068
Triangles
Prints as shown on its floor, no supports. The lid prints as a separate part, top down.
MAIN PURPOSE: Play slide guitar with a bottleneck
A closed-end bottleneck slide for slide guitar: slip it over your ring or little finger and glide it along the strings; the closed tip stops it slipping off.
Printing notes
13.3 cm³
Volume
16.5 g
Est. weight
680
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Store and browse 7-inch singles
A crate for about a hundred 7-inch singles: the sleeves stand a little proud of the sides so you can flip through them, with carry holes at each side and a slatted front.
Printing notes
139.5 cm³
Volume
173.0 g
Est. weight
3,132
Triangles
Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.
MAIN PURPOSE: Make square cord from yarn
A lucet, the medieval two-pronged fork for making square, sturdy cord from any yarn: loop the yarn round the horns and lift each loop over in turn; the hole holds the starting tail.
Printing notes
24.3 cm³
Volume
30.1 g
Est. weight
508
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Smooth and compress clay on pots
A thin, slightly flexible kidney rib for smoothing and compressing clay on the wheel or by hand; the two curved edges fit the inside and the outside of a pot.
Printing notes
7.3 cm³
Volume
9.0 g
Est. weight
252
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Rub linocut prints by hand
A baren for printing linocuts and woodcuts by hand: grip the bar and rub the smooth, flat underside over the paper to lift an even print from the inked block.
Printing notes
70.3 cm³
Volume
87.2 g
Est. weight
692
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Spin your own yarn by hand
A rim-weighted whorl for a drop spindle: press it onto an 8 mm dowel with a hook in the end and spin your own yarn; most of the weight sits at the rim, so it spins long and steady.
Printing notes
18.6 cm³
Volume
23.1 g
Est. weight
848
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Weave small first projects on a frame
A frame loom for first weaving projects: wind the warp thread round the notches at the top and bottom, then weave across the open window to make a mug rug or a small wall hanging.
Printing notes
52.6 cm³
Volume
65.3 g
Est. weight
1,308
Triangles
Prints flat as a plate, no supports.
MAIN PURPOSE: Keep sewing pins on your wrist
The base of a wrist pin cushion: stuff a fabric dome into the cup and thread an elastic or hook-and-loop strap through the two slots underneath, so pins are always at hand while you sew or fit.
Printing notes
13.2 cm³
Volume
16.3 g
Est. weight
1,984
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Display sewing bobbins and hold snips
Sewing machine bobbins stand on edge round a ring channel, so every thread colour shows at a glance; the middle holds a seam ripper and snips.
Printing notes
57.2 cm³
Volume
70.9 g
Est. weight
1,008
Triangles
Prints as shown on its floor, no supports.