Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Peg strawberry runners down to root
Peg each new plantlet on a strawberry runner onto a small pot of compost with a U-pin, so it roots while the mother plant still feeds it; after three weeks snip the runner and you have a free plant for next year's bed.
Printing notes
2.2 cm³
Volume
2.8 g
Est. weight
180
Triangles
Print a dozen in PETG. Prints flat as a plate, no supports.
MAIN PURPOSE: Hold drip irrigation tubes at each plant
Push the spike into the soil and snap 4 mm micro drip tube into the C clip at the top: each dripper stays pointed at the root zone of its plant instead of wandering, so the irrigation water goes exactly where it is needed.
Printing notes
4.3 cm³
Volume
5.3 g
Est. weight
188
Triangles
Print a batch in PETG or ASA. Prints flat as a plate, no supports.
MAIN PURPOSE: Release mason bee cocoons safely in spring
Put cleaned mason bee cocoons in the box in spring and hang it beside the bee hotel: the bees chew out and leave through the single 8 mm hole, while birds and mice cannot reach the cocoons and the lid lifts off to clear the empty cases.
Printing notes
50.3 cm³
Volume
62.3 g
Est. weight
13,656
Triangles
Prints as shown on its floor, no supports. The lid prints as a separate part, top down.
MAIN PURPOSE: Dry saved seed with air on all sides
Spread saved bean, tomato or flower seed on the fine grid and stack several screens: the low front and back walls leave a gap between layers, so air flows through every one and the seed dries evenly in a shady spot before you pack it away.
Printing notes
75.5 cm³
Volume
93.6 g
Est. weight
6,104
Triangles
Print several to stack. Prints as shown on its floor, no supports.
MAIN PURPOSE: Fix plant canes to a balcony railing
Snaps onto a round balcony handrail up to 43 mm and holds a 12 mm cane upright beside it: two clamps per cane turn a rented balcony into a trellis for tomatoes, beans or sweet peas, with no drilling and no wire round the railing.
Printing notes
32.6 cm³
Volume
40.4 g
Est. weight
2,076
Triangles
Print as it comes in PETG.
MAIN PURPOSE: Water grow-bag plants at the roots
Press it 3 cm into a grow bag round a tomato or pepper: water poured inside soaks down to the roots instead of running off the plastic, and the open grid floor lets you top up with extra compost for a deeper root run.
Printing notes
53.7 cm³
Volume
66.6 g
Est. weight
1,392
Triangles
Print three per grow bag. Prints as shown on its floor, no supports.
MAIN PURPOSE: Keep a dragged hose off garden beds
Push one in at each corner of a bed: the hose slides round the curved head as you pull it along, instead of dragging across the bed and flattening the plants, and the upturned crescent tips stop it riding over the top.
Printing notes
26.4 cm³
Volume
32.8 g
Est. weight
996
Triangles
Print as it comes in ASA or PETG.
MAIN PURPOSE: Tell solar time from a string shadow
A sundial whose gnomon is a taut string: tie a cord from the hole at the front to the hole at the top of the fin, and its shadow falls on the engraved hours. Set for about 50 degrees north; face the fin due north and read local solar time.
Printing notes
162.2 cm³
Volume
201.1 g
Est. weight
13,414
Triangles
Print in ASA or PETG for the garden. Prints flat as a plate, no supports.
MAIN PURPOSE: Scatter sound reflections in a small studio
A one-dimensional diffuser for a home studio: seven steps whose heights follow the quadratic-residue sequence for the prime 7 scatter mid and high reflections evenly instead of bouncing them straight back, taming flutter echo. Hang a row on the wall behind the speakers.
Printing notes
1,120.8 cm³
Volume
1,389.8 g
Est. weight
144
Triangles
Print several and tile them, rotated 90 degrees in turn. Prints as shown on its floor, no supports.
MAIN PURPOSE: Cast up and down light from an LED puck
Stick a battery LED puck light to the inside of the back wall and hang the sconce on two screws: light washes up through the open top and down through the floor opening onto the wall, while a soft glow leaks through the slotted front. No wiring needed.
Printing notes
38.3 cm³
Volume
47.5 g
Est. weight
8,950
Triangles
Prints as shown on its floor, no supports.