Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Serve crackers standing on edge
Crackers and crispbread stand on edge in two long lanes beside the cheese board, so everyone can take one without the pile sliding over.
Printing notes
46.1 cm³
Volume
57.1 g
Est. weight
2,952
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Build a stackable honeycomb wine rack
One cell of a honeycomb wine rack: print several, lay them on their sides and stack them. The bottle slides in neck first, its shoulder resting against the end wall while the neck pokes through.
Printing notes
115.9 cm³
Volume
143.7 g
Est. weight
236
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Keep honey and its dipper together
A hexagonal honey pot whose lift-off top has a hole near the edge for the dipper handle, so the dipper stays in the honey and the top still sits flat. HONEY is engraved on the top.
Printing notes
95.5 cm³
Volume
118.4 g
Est. weight
1,952
Triangles
Prints as shown on its floor, no supports. Stacked parts are fused into one print.
MAIN PURPOSE: Help toddlers hold a juice box
A rigid sleeve for a 200 ml juice box with two chunky handles, so small hands can hold it without squeezing juice up the straw.
Printing notes
29.0 cm³
Volume
35.9 g
Est. weight
4,240
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Butter bread easily with one hand
For anyone cooking with one hand: push a slice of bread into the raised corner and it stays put while you spread it. Grip feet stop the board sliding.
Printing notes
176.9 cm³
Volume
219.3 g
Est. weight
84
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Help one-handed eaters scoop food
A plate for eating one-handed or with a weak grip: food pushed towards the tall, curved back wall rolls up onto the spoon instead of off the edge, and grip feet hold the plate still.
Printing notes
146.5 cm³
Volume
181.6 g
Est. weight
1,678
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Hold vacuum bags upright in water bath
Stands vacuum bags upright in five slots so the water circulates round every bag in the bath; the open floor and slotted walls let it flow. Print it in PETG for cooking temperatures.
Printing notes
229.7 cm³
Volume
284.8 g
Est. weight
8,050
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Support a loaded paper plate
A rigid holder for a 23 cm (9-inch) paper plate at picnics and barbecues, so a loaded plate never folds in your hand.
Printing notes
117.4 cm³
Volume
145.5 g
Est. weight
680
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Hold dipped cake pops while setting
Stand eight freshly dipped cake pops or lollipops upright to set: the sticks drop through the top into the box below, which keeps them straight and the stand steady.
Printing notes
89.9 cm³
Volume
111.5 g
Est. weight
3,628
Triangles
Prints as shown on its floor, no supports. Stacked parts are fused into one print.
MAIN PURPOSE: Dry herbs and chillies with airflow
Hang it from a hook or a beam by four cords: herbs, chillies or flowers dry evenly on the perforated floor with air all round them.
Printing notes
95.8 cm³
Volume
118.8 g
Est. weight
21,264
Triangles
Prints as shown on its floor, no supports.