Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Trim an even beard neckline
Hold the curved guide under the jaw and run the trimmer along its edge: the neckline comes out as one clean, symmetrical curve, the same line every week instead of creeping higher each time.
Printing notes
8.1 cm³
Volume
10.0 g
Est. weight
352
Triangles
Print flat in PETG.
MAIN PURPOSE: Dry and store a wig with air all round
A wig dries and keeps its style on this stand: the open crown ring with six ribs and six vent holes lets air through the cap from inside, unlike a solid foam head, and the 180 mm post holds long hair clear of the dresser.
Printing notes
149.8 cm³
Volume
185.8 g
Est. weight
4,736
Triangles
Print the post with 4 walls. Prints as shown on its floor, no supports. Stacked parts are fused into one print.
MAIN PURPOSE: Shorten a metal watch bracelet at home
Stand the metal bracelet on edge in one of the two channels with a link pin over the slot and tap the pin out with a punch: the block holds the bracelet square and the pin drops through the floor slot instead of disappearing.
Printing notes
17.9 cm³
Volume
22.2 g
Est. weight
2,424
Triangles
Print solid (100% infill) in PETG. Prints as shown on its floor, no supports.
MAIN PURPOSE: Keep mascara off the eyelid
Hold the curved card along the lash line with the thumb tab while you apply mascara: stray strokes land on the shield, not on the eyelid or under the eye, so there is nothing to wipe off afterwards.
Printing notes
2.2 cm³
Volume
2.7 g
Est. weight
368
Triangles
Print flat in PETG; wipe clean.
MAIN PURPOSE: Dry makeup brushes bristles down
Push each washed brush handle-first up through the hole where it wedges: the bristles hang down and dry, so water never runs into the ferrule and loosens the glue. Eight holes from 6 to 13 mm cover slim liners to fat powder brushes.
Printing notes
79.9 cm³
Volume
99.0 g
Est. weight
2,328
Triangles
Prints as shown on its floor, no supports. Stacked parts are fused into one print.
MAIN PURPOSE: Repair broken pressed powder makeup
Crush a broken eyeshadow or blusher, wet it with a few drops of surgical spirit, cover with kitchen paper and press with this 25 mm tamper: the powder sets into a smooth, solid cake again instead of being thrown away.
Printing notes
8.2 cm³
Volume
10.2 g
Est. weight
2,200
Triangles
Prints as shown on its floor, no supports. Stacked parts are fused into one print.
MAIN PURPOSE: Let painted nails dry without smudges
Rest the palm in the tray and the fingertips on the five posts: the pads of the fingers take the weight and the wet nails float in the air, so a fresh manicure dries without a single smudge.
Printing notes
57.6 cm³
Volume
71.5 g
Est. weight
5,204
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Deep-clean makeup brushes on a ridged floor
Swirl a soapy brush over the wave ridges on the floor and they work cleanser deep into the bristles; the fillet corners rinse clean and the rounded rim is kind to bristles as you squeeze them out.
Printing notes
37.7 cm³
Volume
46.8 g
Est. weight
8,084
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Raise a foot safely for shaving in the shower
Stand it on the shower floor against the wall and put one foot on the 15 degree tread: the leg is raised and bent for shaving or washing without balancing on one foot on a wet floor. The trussed profile carries full body weight.
Printing notes
407.6 cm³
Volume
505.5 g
Est. weight
764
Triangles
Print as it comes (profile on the bed) in PETG, 40% infill.
MAIN PURPOSE: Hang a bar of soap on a magnet to dry
Screw the cup under a shelf or the shower caddy, press a 20 x 3 mm magnet into it, and push a steel bottle cap into the back of the soap bar: the soap hangs in the air, dries all round and never sits in a slimy dish again.
Printing notes
2.5 cm³
Volume
3.1 g
Est. weight
848
Triangles
Add a 20 x 3 mm magnet and a steel bottle cap. Prints as shown on its floor, no supports.