Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Leeuwenhoek ball-lens microscope
By Krypto
Complexity
Simple
Others Science & education
0
Leeuwenhoek ball-lens microscope
MAIN PURPOSE: See cells with a single glass bead lens
A slide-sized plate with seats for a 2 mm and a 3 mm glass bead, the trick Antonie van Leeuwenhoek used in the 1670s: tape a specimen to the back, hold the bead to your eye and see cells at up to 150 times, with a lens that cost almost nothing.
Printing notes
3.9 cm³
Volume
4.9 g
Est. weight
5,148
Triangles

Glue in 2 mm and 3 mm glass beads. Prints flat as a plate, no supports.

AR view Open in app
Preview of Eureka overflow can for rock density
By Krypto
Complexity
Simple
Others Science & education
0
Eureka overflow can for rock density
MAIN PURPOSE: Measure rock volume and density by displacement
Fill the can until water runs from the spout, lower in a rock on a thread and catch the overflow in a measuring cylinder: that is the rock volume. Divide its weight by it and pupils can tell granite from basalt from a lump of pyrite by density alone.
Printing notes
14.5 cm³
Volume
18.0 g
Est. weight
2,684
Triangles

PETG, 3 walls; push a short drinking straw into the spout. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Newton colour wheel spinner
By Krypto
Complexity
Simple
Others Science & education
0
Newton colour wheel spinner
MAIN PURPOSE: Show that the spectrum colours mix to white
Colour the seven ribbed sectors red, orange, yellow, green, blue, indigo and violet, push a pencil through the centre and spin it like a top: the colours blend into a pale grey white, Newton's proof that white light is all the colours together.
Printing notes
20.0 cm³
Volume
24.9 g
Est. weight
1,708
Triangles

White PLA, colour it with markers. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Petri dish stacking column
By Krypto
Complexity
Multi-part assembly
Others Science & education
0
Petri dish stacking column
MAIN PURPOSE: Store and dispense petri dishes
Keeps a stack of 90 mm petri dishes clean and upright on the lab bench or in the incubator: take a dish out through the side window and close the top with the telescoping lid.
Printing notes
79.4 cm³
Volume
98.5 g
Est. weight
5,672
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging. The lid prints as a separate part, top down.

AR view Open in app
Preview of Microscope slide box for four stacks
By Krypto
Complexity
Multi-part assembly
Others Science & education
0
Microscope slide box for four stacks
MAIN PURPOSE: Store microscope slides
Keeps glass microscope slides sorted in four stacks, prepared samples on one side and blanks on the other, with a telescoping lid against dust; the engraved labels take a pencil note.
Printing notes
96.0 cm³
Volume
119.0 g
Est. weight
10,568
Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Bug viewer box
By Krypto
Complexity
Multi-part assembly
Others Science & education
0
Bug viewer box
MAIN PURPOSE: Observe small creatures for nature study
Catch and watch beetles, woodlice and snails for a few minutes before letting them go: tape clear film over the round window, the slotted sides let air in, and the lid lifts off to release them.
Printing notes
124.8 cm³
Volume
154.7 g
Est. weight
4,876
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging. The lid prints as a separate part, top down.

AR view Open in app
Preview of Root viewer planter
By Krypto
Complexity
Medium
Others Science & education
0
Root viewer planter
MAIN PURPOSE: Show children how roots grow
Watch roots grow: tape clear acetate over the big window on the inside, plant beans or carrots right against it, and keep the window covered with card between peeks.
Printing notes
48.1 cm³
Volume
59.7 g
Est. weight
2,156
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of Place value counting tray
By Krypto
Complexity
Medium
Others Science & education
0
Place value counting tray
MAIN PURPOSE: Teach place value with counters
A maths tray for hundreds, tens and ones: sort counters, sticks or beads into the three columns to build numbers and practise carrying and borrowing.
Printing notes
75.6 cm³
Volume
93.7 g
Est. weight
2,332
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Butterfly spreading board
By Krypto
Complexity
Simple
Others Science & education
0
Butterfly spreading board
MAIN PURPOSE: Set insect specimens for display
Set butterflies and moths for a collection: the insect's body sits in the central channel while the wings are pinned flat on foam strips either side until they dry.
Printing notes
94.2 cm³
Volume
116.8 g
Est. weight
1,016
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Spectrophotometer cuvette rack
By Krypto
Complexity
Advanced
Others Science & education
0
Spectrophotometer cuvette rack
MAIN PURPOSE: Hold laboratory cuvettes in order
Holds eight standard 12.5 mm square cuvettes upright in a row, in the order you will read them, so samples never get mixed up on the bench.
Printing notes
22.3 cm³
Volume
27.7 g
Est. weight
6,288
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan