Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Board centre finder
By Krypto
Complexity
Advanced
Workshop Woodworking
0
Board centre finder
MAIN PURPOSE: Mark the centre line of a board edge
Finds the centre of any board edge in seconds: hold the two pins against both faces, turn until they touch, and mark through the centre hole.
Printing notes
18.0 cm³
Volume
22.4 g
Est. weight
1,652
Triangles

Flip it so the pins point down onto the work. Prints flat as a plate, no supports.

AR view Open in app
Preview of Jointer and router push block
By Krypto
Complexity
Advanced
Workshop Woodworking
0
Jointer and router push block
MAIN PURPOSE: Feed boards safely past a cutter
Keeps your hands well above the cutter when you feed a board over a jointer or across a router table: hold the tall handle and press the grippy base down onto the wood.
Printing notes
70.8 cm³
Volume
87.7 g
Est. weight
2,008
Triangles

Print the base in TPU, or stick rubber grip tape underneath. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Ruler stop block
By Krypto
Complexity
Simple
Workshop Tools & jigs
0
Ruler stop block
MAIN PURPOSE: Repeat measurements quickly
Slides onto a 25 mm steel rule and locks with a small screw, so you can mark the same measurement again and again without reading the scale.
Printing notes
2.6 cm³
Volume
3.3 g
Est. weight
1,816
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of Router circle cutting jig
By Krypto
Complexity
Medium
Workshop Woodworking
0
Router circle cutting jig
MAIN PURPOSE: Cut circles with a router
Cuts perfect circles with a palm router: screw the router base to the wide end, put a nail through one of the pivot holes into the centre of the board, and swing the router round.
Printing notes
67.9 cm³
Volume
84.2 g
Est. weight
1,988
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Air compressor fittings caddy
By Krypto
Complexity
Advanced
Workshop Workshop storage
0
Air compressor fittings caddy
MAIN PURPOSE: Store compressor couplers, nozzles and tape
Everything for the compressor in one wall caddy: four bays for couplers, plugs, nozzles and the tyre chuck, a round side cup for thread-seal tape, and two keyholes to hang it by.
Printing notes
124.9 cm³
Volume
154.9 g
Est. weight
2,960
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Paintbrush keeper
By Krypto
Complexity
Multi-part assembly
Workshop Finishing & painting
0
Paintbrush keeper
MAIN PURPOSE: Keep loaded brushes wet between coats
Keep a loaded brush or roller sleeve wet between coats: wrap it in cling film, lay it in the long box and close the telescoping lid, and it is ready to go the next morning.
Printing notes
193.7 cm³
Volume
240.2 g
Est. weight
9,940
Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Model kit sprue and parts tray
By Krypto
Complexity
Medium
Workshop Workshop storage
0
Model kit sprue and parts tray
MAIN PURPOSE: Organise sprues and cut-off model parts
A build tray for plastic model kits: sprue frames stand upright in four slots on the left, and the right side has bays for cut-off parts so nothing tiny goes missing before it is glued.
Printing notes
128.6 cm³
Volume
159.4 g
Est. weight
1,064
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Mini roller paint tray
By Krypto
Complexity
Medium
Workshop Finishing & painting
0
Mini roller paint tray
MAIN PURPOSE: Load mini rollers with paint
A tray for 10 cm mini rollers: paint goes in the deep front well behind a low dam, and you roll off the excess on the ribbed floor behind it.
Printing notes
79.6 cm³
Volume
98.7 g
Est. weight
11,252
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Model railway servicing cradle
By Krypto
Complexity
Simple
Workshop Tools & jigs
0
Model railway servicing cradle
MAIN PURPOSE: Hold locomotives upside down for servicing
Lay a locomotive or coach upside down in the rounded channel to clean its wheels or service the motor; the open ends take models longer than the cradle. Line it with foam to protect the paint.
Printing notes
46.2 cm³
Volume
57.2 g
Est. weight
4,150
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Ladder-top tool tray
By Krypto
Complexity
Simple
Workshop Workshop storage
0
Ladder-top tool tray
MAIN PURPOSE: Hold paint and screws on a ladder
Sits on top of a stepladder: one half takes a paint tin or a tub of filler, the other has bays for screws and a pencil, and grip feet stop it sliding off while you work.
Printing notes
178.2 cm³
Volume
221.0 g
Est. weight
2,916
Triangles

Prints as shown on its floor, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan