Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Add flush pulls to doors and drawers
Press it into a 35 mm hole drilled in a sliding door, a cupboard without handles or a drawer front for a neat finger pull that sits flush. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
8.0 cm³
Volume
9.9 g
Est. weight
840
Triangles
Print floor-down as shown, then turn it over to use it.
MAIN PURPOSE: Hang pictures from a picture rail
Hangs pictures from a traditional picture rail moulding without drilling the walls: hook it over the rail and hang the frame wire from the hook at the bottom.
Printing notes
10.6 cm³
Volume
13.2 g
Est. weight
568
Triangles
Print flat in PETG.
MAIN PURPOSE: Hold a mezuzah scroll on a doorpost
A slim, simple case for a mezuzah scroll up to 10 cm: roll the scroll into the case, close the telescoping lid and fix it to the doorpost through the two screw holes.
Printing notes
3.9 cm³
Volume
4.9 g
Est. weight
5,282
Triangles
Prints as shown on its floor, no supports. The lid prints as a separate part, top down.
MAIN PURPOSE: Guide rainwater down from the gutter
One cup of a rain chain to hang from the gutter instead of a downpipe: link a string of them through the rim holes and rainwater splashes from cup to cup down through the centre holes.
Printing notes
20.0 cm³
Volume
24.8 g
Est. weight
3,376
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Display small plants and candles on walls
An arched niche for the wall with a shelf across the middle: hang it by the two screw holes in the back and show off small plants, candles in jars or a stack of postcards.
Printing notes
268.6 cm³
Volume
333.0 g
Est. weight
820
Triangles
Prints as shown on its outline, no supports.
MAIN PURPOSE: Cover a toggle light switch
A cover plate for a standard North American single toggle switch, with screw holes 83.3 mm apart and a softly rounded edge; print it in a colour that matches the wall. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
15.6 cm³
Volume
19.4 g
Est. weight
1,996
Triangles
Print floor-down as shown, then turn it over to use it.
MAIN PURPOSE: Dry and separate folding umbrellas
A slim stand for folding umbrellas by the door: four dividers keep up to four apart so they dry, and the drips collect in the closed base.
Printing notes
361.7 cm³
Volume
448.4 g
Est. weight
1,112
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Hang honeycomb shelves on the wall
A deep hexagon cubby that screws to the wall; print a few and hang them in a honeycomb.
Printing notes
201.2 cm³
Volume
249.5 g
Est. weight
396
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Lift furniture legs higher off the floor
A ribbed cup that lifts a table, desk or sofa leg up to 80 mm wide by six centimetres; print one per leg.
Printing notes
151.6 cm³
Volume
188.0 g
Est. weight
912
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Hide valuables in a floating shelf
A floating wall shelf whose top lifts off to reveal a hidden compartment for keys, passports or cash; hangs from two keyholes.
Printing notes
232.3 cm³
Volume
288.0 g
Est. weight
3,460
Triangles
Prints as shown on its floor, no supports. The lid prints as a separate part, top down.