Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Ruler stop block
By Krypto
Complexity
Simple
Workshop Tools & jigs
0
Ruler stop block
MAIN PURPOSE: Repeat measurements quickly
Slides onto a 25 mm steel rule and locks with a small screw, so you can mark the same measurement again and again without reading the scale.
Printing notes
2.6 cm³
Volume
3.3 g
Est. weight
1,816
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of Model railway servicing cradle
By Krypto
Complexity
Simple
Workshop Tools & jigs
0
Model railway servicing cradle
MAIN PURPOSE: Hold locomotives upside down for servicing
Lay a locomotive or coach upside down in the rounded channel to clean its wheels or service the motor; the open ends take models longer than the cradle. Line it with foam to protect the paint.
Printing notes
46.2 cm³
Volume
57.2 g
Est. weight
4,150
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Drill and dowel size gauge
By Krypto
Complexity
Advanced
Workshop Tools & jigs
0
Drill and dowel size gauge
MAIN PURPOSE: Identify drill bit and dowel sizes
A flat gauge with eight holes from 3 to 14 mm and the size engraved under each, for identifying drill bits, dowels and bolts.
Printing notes
50.9 cm³
Volume
63.1 g
Est. weight
11,256
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Speed square fitted tray
By Krypto
Complexity
Simple
Workshop Tools & jigs
0
Speed square fitted tray
MAIN PURPOSE: Store a rafter speed square
A tray with a recess shaped exactly like a 7-inch rafter square, so it always goes back in the same place.
Printing notes
439.7 cm³
Volume
545.2 g
Est. weight
1,224
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Wire stripper drawer shadow board
By Krypto
Complexity
Simple
Workshop Tools & jigs
0
Wire stripper drawer shadow board
MAIN PURPOSE: Store wire strippers in a drawer
A thin shadow board for a tool drawer with a recess shaped like a pair of wire strippers.
Printing notes
101.2 cm³
Volume
125.5 g
Est. weight
748
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Ratchet and socket fitted tray
By Krypto
Complexity
Simple
Workshop Tools & jigs
0
Ratchet and socket fitted tray
MAIN PURPOSE: Organise a ratchet and sockets
A shadow tray with a ratchet-shaped recess and a row of four sockets in rising sizes.
Printing notes
272.0 cm³
Volume
337.3 g
Est. weight
2,716
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Whetstone drip tray
By Krypto
Complexity
Simple
Workshop Tools & jigs
0
Whetstone drip tray
MAIN PURPOSE: Catch slurry under a whetstone
The stone sits inside an inner wall while water and slurry run off into the channel around it, on small feet.
Printing notes
95.4 cm³
Volume
118.3 g
Est. weight
2,352
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Tap and die fitted case
By Krypto
Complexity
Multi-part assembly
Workshop Tools & jigs
0
Tap and die fitted case
MAIN PURPOSE: Store taps and dies in a case
A fitted case with five round die pockets and a T-handle recess, closed with a telescoping lid shown beside it.
Printing notes
364.2 cm³
Volume
451.6 g
Est. weight
6,496
Triangles

Prints as shown on its floor, no supports. The lid prints as a separate part, top down.

AR view Open in app
Preview of Parts washing basket
By Krypto
Complexity
Medium
Workshop Tools & jigs
0
Parts washing basket
MAIN PURPOSE: Dunk small parts in cleaner
A basket with honeycomb perforations in the floor and walls and handle slots, for dunking small parts in cleaner.
Printing notes
66.6 cm³
Volume
82.6 g
Est. weight
18,228
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of Right-angle drill guide block
By Krypto
Complexity
Advanced
Workshop Tools & jigs
0
Right-angle drill guide block
MAIN PURPOSE: Keep drill bits square to work
Two plates 34 mm apart with matching 4, 6, 8 and 10 mm holes keep the bit square to the work: hold the block down and drill straight through.
Printing notes
30.2 cm³
Volume
37.4 g
Est. weight
1,496
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan