Showcase
Models Showcase
Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Shade a pendant bulb with honeycomb light
A honeycomb-perforated pendant shade that hangs from a standard E27 lampholder through the hole in its top; use an LED bulb of 10 W or less. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
64.5 cm³
Volume
80.0 g
Est. weight
22,392
Triangles
Print floor-down as shown, then turn it over to use it.
MAIN PURPOSE: Display small plants and candles on walls
An arched niche for the wall with a shelf across the middle: hang it by the two screw holes in the back and show off small plants, candles in jars or a stack of postcards.
Printing notes
268.6 cm³
Volume
333.0 g
Est. weight
820
Triangles
Prints as shown on its outline, no supports.
MAIN PURPOSE: Catch meltwater under wet boots
A boot tray for one pair of wet or muddy boots: four low ribs hold the soles above the meltwater and grit, and the raised rim keeps it off the floor.
Printing notes
171.0 cm³
Volume
212.0 g
Est. weight
2,940
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Water herbs automatically from a reservoir
A herb pot that sits on its own water reservoir: a cotton wick through the centre hole draws water up to the roots, and you top up through the window in the front.
Printing notes
86.9 cm³
Volume
107.8 g
Est. weight
4,448
Triangles
Prints as shown on its floor, no supports. Stacked parts are fused into one print.
MAIN PURPOSE: Root plant cuttings in water
A rack for five 16 mm glass test tubes: put a cutting in each and watch the roots grow, with the glass doing the water-holding.
Printing notes
45.8 cm³
Volume
56.8 g
Est. weight
3,156
Triangles
Prints as shown on its floor, no supports. Stacked parts are fused into one print.
MAIN PURPOSE: Grow and train a bonsai tree
A shallow training pot on feet with two large drain holes and four small holes for wiring the tree in, with chamfered corners and rims.
Printing notes
82.3 cm³
Volume
102.1 g
Est. weight
1,804
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Give orchid roots plenty of air
A square pot slotted on every side and perforated underneath, so orchid roots get the air they need, on small feet.
Printing notes
31.0 cm³
Volume
38.5 g
Est. weight
85,768
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Hold air plants open to light
An open hexagon cradle with a perforated floor, so an air plant gets light and air all round; group a few on a shelf.
Printing notes
28.0 cm³
Volume
34.8 g
Est. weight
5,968
Triangles
Prints as shown on its floor, no supports.
MAIN PURPOSE: Grow cat grass on a drip tray
A planter for cat grass with drain holes, sitting on its own drip tray, with two paw prints raised on the front.
Printing notes
89.3 cm³
Volume
110.8 g
Est. weight
4,624
Triangles
Prints as shown on its floor, no supports. Stacked parts are fused into one print.
MAIN PURPOSE: Measure rainfall in the garden
A square-walled rain gauge with a millimetre scale engraved up the front: straight walls mean the water depth is the rainfall; hangs on a fence from two keyholes.
Printing notes
9.5 cm³
Volume
11.8 g
Est. weight
15,436
Triangles
Prints as shown on its floor, no supports.