Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Stackable worm farm tray
By Krypto
Complexity
Medium
Others Garden & plants
0
Stackable worm farm tray
MAIN PURPOSE: Compost kitchen scraps with worms
One tray of a worm composting tower: stack two or three, start the worms in the bottom one, and as each tray fills they climb up through the floor holes towards fresh scraps.
Printing notes
195.4 cm³
Volume
242.3 g
Est. weight
2,352
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Ikebana flower frog
By Krypto
Complexity
Advanced
Others Garden & plants
0
Ikebana flower frog
MAIN PURPOSE: Arrange cut flowers in a shallow bowl
Holds cut stems upright in a shallow bowl or vase: push each stem into a hole in the weighted frog, the way a metal kenzan pin holder would.
Printing notes
43.9 cm³
Volume
54.5 g
Est. weight
2,160
Triangles

Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Garden cane connector
By Krypto
Complexity
Medium (set)
Others Garden & plants
0
Garden cane connector
MAIN PURPOSE: Build garden frames from canes
Joins bamboo canes up to 10 mm thick at right angles: push them into the side holes and the top to build frames for netting, climbing beans or a mini greenhouse.
Printing notes
3.1 cm³
Volume
3.9 g
Est. weight
1,832
Triangles

Print several in PETG or ASA. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Pond plant basket
By Krypto
Complexity
Medium
Others Garden & plants
0
Pond plant basket
MAIN PURPOSE: Plant aquatic plants in a pond
An aquatic planting basket for water lilies and marginal plants: the open lattice lets roots and water through while holding the soil in place; line it with hessian.
Printing notes
77.7 cm³
Volume
96.3 g
Est. weight
22,352
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Plant pot feet
By Krypto
Complexity
Medium (set)
Others Garden & plants
0
Plant pot feet
MAIN PURPOSE: Raise plant pots for drainage
Lift a planter a couple of centimetres off a patio or a shelf so water drains out and the base doesn't rot or stain: set three feet under the pot, wave face out. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
8.2 cm³
Volume
10.2 g
Est. weight
1,604
Triangles

Print three, in PETG or ASA for outdoor pots. Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Plant saucer with riser ring
By Krypto
Complexity
Simple
Others Garden & plants
0
Plant saucer with riser ring
MAIN PURPOSE: Catch drainage water without waterlogging roots
A drip saucer that lifts the pot onto an inner ring, so the roots never sit in the water that drains out and the plant doesn't rot.
Printing notes
104.2 cm³
Volume
129.3 g
Est. weight
1,008
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Potting soil sieve
By Krypto
Complexity
Medium
Others Garden & plants
0
Potting soil sieve
MAIN PURPOSE: Sieve fine soil for sowing
Sieves compost and potting soil for seed trays: shake it over the tray, and the fine soil falls through the mesh while stones and roots stay behind.
Printing notes
91.7 cm³
Volume
113.7 g
Est. weight
5,512
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of Seed tray dibber board
By Krypto
Complexity
Advanced
Others Garden & plants
0
Seed tray dibber board
MAIN PURPOSE: Make evenly spaced holes for sowing
Presses five staggered planting holes into a seed tray in one go: fill the tray with compost, press the board down, and drop a seed into each hole.
Printing notes
54.2 cm³
Volume
67.2 g
Est. weight
2,732
Triangles

Flip it so the pegs point down into the tray. Prints flat as a plate, no supports.

AR view Open in app
Preview of Solar garden light stake
By Krypto
Complexity
Medium
Others Garden & plants
0
Solar garden light stake
MAIN PURPOSE: Repair solar garden lights
A replacement stake for a solar garden light whose spike has snapped: push the light's tube into the socket and the square stake into the lawn or border.
Printing notes
11.6 cm³
Volume
14.4 g
Est. weight
788
Triangles

Check the socket fits your light; print in PETG or ASA. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Slug beer trap
By Krypto
Complexity
Medium
Others Garden & plants
0
Slug beer trap
MAIN PURPOSE: Trap slugs and snails with beer
A beer trap for slugs and snails: sink it so the four entrance windows sit just above the soil, half-fill it with beer, and the lift-off roof keeps the rain from diluting it.
Printing notes
63.2 cm³
Volume
78.4 g
Est. weight
10,916
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging. Stacked parts are fused into one print.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan