Showcase

Models Showcase

Models shared by the SO3D.xyz community. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Triangle pedestal tray
By Krypto
Complexity
Simple
Kitchen Serving & table
0
Triangle pedestal tray
MAIN PURPOSE: Raise a triangle tray on a single pedestal for display or serving
A 150 mm triangular tray lifted 45 mm off the table on a single round pedestal with a wide foot, like a small cake stand. The pedestal pushes into the tray on a press-fit peg, so both parts print flat without supports.
Printing notes
73.6 cm³
Volume
91.2 g
Est. weight
584
Triangles

Both parts print flat with no supports. Push the pedestal peg up into the hole in the tray; a drop of glue makes it permanent. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Semicircle two-tier screw-together stand
By Krypto
Complexity
Medium
Kitchen Serving & table
0
Semicircle two-tier screw-together stand
MAIN PURPOSE: Serve sweets, fruit or trinkets on two semicircle tiers that screw together
A two-tier stand of half-moon trays, 150 and 130 mm across, the top one held 30 mm above the bottom one on a slim screw-in column, on a single round pedestal with a wide foot. It comes apart flat for storage, and every part prints on its own without supports.
Printing notes
84.5 cm³
Volume
104.8 g
Est. weight
5,828
Triangles

Every part prints flat with no supports. Screw the column onto the stud in the bottom tray, screw the top tray on, and push the pedestal peg up into the bottom tray. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Semicircle pedestal tray
By Krypto
Complexity
Simple
Kitchen Serving & table
0
Semicircle pedestal tray
MAIN PURPOSE: Raise a semicircle tray on a single pedestal for display or serving
A 150 mm half-moon tray lifted 45 mm off the table on a single round pedestal with a wide foot, like a small cake stand. The pedestal pushes into the tray on a press-fit peg, so both parts print flat without supports.
Printing notes
45.8 cm³
Volume
56.8 g
Est. weight
848
Triangles

Both parts print flat with no supports. Push the pedestal peg up into the hole in the tray; a drop of glue makes it permanent. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Rounded-square two-tier screw-together stand
By Krypto
Complexity
Medium
Kitchen Serving & table
0
Rounded-square two-tier screw-together stand
MAIN PURPOSE: Serve sweets, fruit or trinkets on two rounded-square tiers that screw together
A two-tier stand of rounded-square trays, 150 and 130 mm across, the top one held 30 mm above the bottom one on a slim screw-in column, on a single round pedestal with a wide foot. It comes apart flat for storage, and every part prints on its own without supports.
Printing notes
157.6 cm³
Volume
195.5 g
Est. weight
6,380
Triangles

Every part prints flat with no supports. Screw the column onto the stud in the bottom tray, screw the top tray on, and push the pedestal peg up into the bottom tray. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Rounded-square pedestal tray
By Krypto
Complexity
Simple
Kitchen Serving & table
0
Rounded-square pedestal tray
MAIN PURPOSE: Raise a rounded-square tray on a single pedestal for display or serving
A 150 mm rounded-square tray lifted 45 mm off the table on a single round pedestal with a wide foot, like a small cake stand. The pedestal pushes into the tray on a press-fit peg, so both parts print flat without supports.
Printing notes
94.7 cm³
Volume
117.5 g
Est. weight
1,124
Triangles

Both parts print flat with no supports. Push the pedestal peg up into the hole in the tray; a drop of glue makes it permanent. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Triangle three-tier screw-together stand
By Krypto
Complexity
Advanced
Kitchen Serving & table
0
Triangle three-tier screw-together stand
MAIN PURPOSE: Serve sweets, fruit or trinkets on three triangle tiers that screw together
A tiered stand of three triangular trays, 150, 130 and 110 mm across, each held 30 mm above the one below on a slim screw-in column, on a single round pedestal with a wide foot. It comes apart flat for storage, and every part prints on its own without supports.
Printing notes
159.0 cm³
Volume
197.1 g
Est. weight
10,016
Triangles

Every part prints flat with no supports. Screw each column onto the stud in the tray below, screw the next tray on top, and push the pedestal peg up into the bottom tray. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Semicircle three-tier screw-together stand
By Krypto
Complexity
Advanced
Kitchen Serving & table
0
Semicircle three-tier screw-together stand
MAIN PURPOSE: Serve sweets, fruit or trinkets on three semicircle tiers that screw together
A tiered stand of three half-moon trays that sit flat against a wall or the back of a counter, 150, 130 and 110 mm across, each held 30 mm above the one below on a slim screw-in column, on a single round pedestal with a wide foot. It comes apart flat for storage, and every part prints on its own without supports.
Printing notes
117.3 cm³
Volume
145.4 g
Est. weight
10,808
Triangles

Every part prints flat with no supports. Screw each column onto the stud in the tray below, screw the next tray on top, and push the pedestal peg up into the bottom tray. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Rounded-square three-tier screw-together stand
By Krypto
Complexity
Advanced
Kitchen Serving & table
0
Rounded-square three-tier screw-together stand
MAIN PURPOSE: Serve sweets, fruit or trinkets on three rounded-square tiers that screw together
A tiered stand of three rounded-square trays, halfway between a square and a circle, 150, 130 and 110 mm across, each held 30 mm above the one below on a slim screw-in column, on a single round pedestal with a wide foot. It comes apart flat for storage, and every part prints on its own without supports.
Printing notes
208.5 cm³
Volume
258.5 g
Est. weight
11,636
Triangles

Every part prints flat with no supports. Screw each column onto the stud in the tray below, screw the next tray on top, and push the pedestal peg up into the bottom tray. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Hexagon three-tier screw-together stand
By Krypto
Complexity
Advanced
Kitchen Serving & table
0
Hexagon three-tier screw-together stand
MAIN PURPOSE: Serve sweets, fruit or trinkets on three hexagon tiers that screw together
A tiered stand of three honeycomb-shaped hexagon trays, 150, 130 and 110 mm across, each held 30 mm above the one below on a slim screw-in column, on a single round pedestal with a wide foot. It comes apart flat for storage, and every part prints on its own without supports.
Printing notes
170.4 cm³
Volume
211.3 g
Est. weight
10,124
Triangles

Every part prints flat with no supports. Screw each column onto the stud in the tray below, screw the next tray on top, and push the pedestal peg up into the bottom tray. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Octagon three-tier screw-together stand
By Krypto
Complexity
Advanced
Kitchen Serving & table
0
Octagon three-tier screw-together stand
MAIN PURPOSE: Serve sweets, fruit or trinkets on three octagon tiers that screw together
A tiered stand of three eight-sided octagon trays, 150, 130 and 110 mm across, each held 30 mm above the one below on a slim screw-in column, on a single round pedestal with a wide foot. It comes apart flat for storage, and every part prints on its own without supports.
Printing notes
177.6 cm³
Volume
220.2 g
Est. weight
10,196
Triangles

Every part prints flat with no supports. Screw each column onto the stud in the tray below, screw the next tray on top, and push the pedestal peg up into the bottom tray. Prints as shown on its floor, no supports. Stacked parts are fused into one print.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan