Vaze — Textured Vases and Bowls
Open any model to make it your size, then download STL or 3MF. All collections
Five curvy shapes (a low dish, a tall vase, a bottle, a footed bowl and a gourd vase) in twenty-five finishes: pleated swirl, knurl, basket weave, spiral, ringed, fluted, reeded, smooth, faceted, fine faceted, grid, honeycomb, diamond, wave, round, slot, vertical slot, gate slot, Voronoi, chevron, fish scale, Greek key, triangle grid, brick and stone. Every model prints without supports, and you c
Prints in one piece with no supports. Change the size, the belly or the neck in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
The legs print separately and press into holes under the bowl, so every part prints flat with no supports. Change the size or the pattern size in the editor to make your own.
Print the bowl upright and the three legs lying flat. Use 0.16 mm layers or finer for a crisp pattern. For food, use a food-safe filament or a liner. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the height, the belly or the neck in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the size, the curve or the pattern size in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern and its border print crisp. No supports needed. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the height, the diameter or the curve in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the size, the belly or the neck in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
The legs print separately and press into holes under the bowl, so every part prints flat with no supports. Change the size or the pattern size in the editor to make your own.
Print the bowl upright and the three legs lying flat. Use 0.16 mm layers or finer for a crisp pattern. For food, use a food-safe filament or a liner. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the height, the belly or the neck in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the size, the curve or the pattern size in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern and its border print crisp. No supports needed. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the height, the diameter or the curve in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the size, the belly or the neck in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
The legs print separately and press into holes under the bowl, so every part prints flat with no supports. Change the size or the pattern size in the editor to make your own.
Print the bowl upright and the three legs lying flat. Use 0.16 mm layers or finer for a crisp pattern. For food, use a food-safe filament or a liner. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the height, the belly or the neck in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the size, the curve or the pattern size in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern and its border print crisp. No supports needed. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the height, the diameter or the curve in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the size, the belly or the neck in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
The legs print separately and press into holes under the bowl, so every part prints flat with no supports. Change the size or the pattern size in the editor to make your own.
Print the bowl upright and the three legs lying flat. Use 0.16 mm layers or finer for a crisp pattern. For food, use a food-safe filament or a liner. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the height, the belly or the neck in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the size, the curve or the pattern size in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern and its border print crisp. No supports needed. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the height, the diameter or the curve in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the size, the belly or the neck in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
The legs print separately and press into holes under the bowl, so every part prints flat with no supports. Change the size or the pattern size in the editor to make your own.
Print the bowl upright and the three legs lying flat. Use 0.16 mm layers or finer for a crisp pattern. For food, use a food-safe filament or a liner. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the height, the belly or the neck in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern stays crisp, and slow down for the upper half. For fresh flowers, put a glass or plastic liner inside. Prints as shown on its floor, no supports.
Prints in one piece with no supports. Change the size, the curve or the pattern size in the editor to make your own.
Use 0.16 mm layers or finer so the 0.8 mm raised pattern and its border print crisp. No supports needed. Prints as shown on its floor, no supports.