Open any model to make it your size, then download STL or 3MF.
All collections
Five curvy shapes (a low dish, a tall vase, a bottle, a footed bowl and a gourd vase) in twenty-five finishes: pleated swirl, knurl, basket weave, spiral, ringed, fluted, reeded, smooth, faceted, fine faceted, grid, honeycomb, diamond, wave, round, slot, vertical slot, gate slot, Voronoi, chevron, fish scale, Greek key, triangle grid, brick and stone. Every model prints without supports, and you c
A tall, slim vase wrapped in sharp pleats that twist 45° around it and swell gently through the middle. 150 mm tall with a 60 mm body (about 80 mm across the pleats), so it suits a single stem, dried flowers or grasses, or pens, brushes and kitchen utensils.
Prints in one piece with no supports. Change the height, the diameter, the pleat depth or the twist in the editor to make your own.
Printing notes
174.5 cm³
Volume
216.4 g
Est. weight
23,784
Triangles
Use 3 walls so the pleats print solid. For fresh flowers in water, print in PETG or stand a glass inside. Prints as shown on its floor, no supports.
MAIN PURPOSE: Display dried flowers or a single stem
A small bottle vase with a round belly and a narrow neck, wrapped in sharp pleats that twist 45° around it. The pleats are deepest at the belly and thin out towards the neck, so it reads like a classic bottle with a swirl. About 110 mm across the pleats and 100 mm tall.
Prints in one piece with no supports. Change the size, the belly or the neck in the editor to make your own.
Printing notes
181.2 cm³
Volume
224.7 g
Est. weight
21,080
Triangles
Silk or dual-colour PLA makes the twist stand out. For fresh flowers in water, print in PETG or stand a glass inside. Prints as shown on its floor, no supports.
MAIN PURPOSE: Catch keys, rings and small trinkets
A low dish wrapped in sharp pleats that twist 45° around it, swelling out at the middle like a spun bowl. About 120 mm across and 30 mm tall, it's a neat catch-all for keys, rings, coins, earbuds or a candle.
Prints in one piece with no supports. Change the size, the pleat depth or the twist in the editor to make your own.
Printing notes
53.7 cm³
Volume
66.6 g
Est. weight
21,056
Triangles
Silk or dual-colour PLA makes the twist stand out; 3 walls keep the pleats solid. Prints as shown on its floor, no supports.
MAIN PURPOSE: Serve fruit and snacks, or hold keys
A wide, shallow bowl wrapped in sharp pleats that twist 45° around it and swell out at the middle, standing on three slim splayed legs. About 150 mm across with a low 25 mm bowl, so it's ideal for fruit, snacks, keys or a candle on a table or shelf.
The legs print separately and press into holes under the bowl, so every part prints flat with no supports. Change the size, the pleat depth or the twist in the editor to make your own.
Printing notes
116.0 cm³
Volume
143.8 g
Est. weight
39,828
Triangles
Print the three legs separately and press them into the holes underneath; a drop of glue makes them permanent. Prints as shown on its floor, no supports.
MAIN PURPOSE: Display a single stem or dried flowers
A tall gourd-shaped vase with a low round belly and a long slim neck that flares out at the lip, wrapped in sharp pleats that twist 45° around it. The pleats are deepest at the belly and fade away up the neck, so the swirl looks like it's spinning upward. About 110 mm across the pleats and 150 mm tall, made for a single stem or a few dried flowers.
Prints in one piece with no supports. Change the height, the belly or the neck in the editor to make your own.
Printing notes
181.9 cm³
Volume
225.5 g
Est. weight
105,380
Triangles
Slow the print down for the slim neck, or print two at once, so each small layer can cool. Silk or dual-colour PLA makes the twist stand out. For fresh flowers, print in PETG or slip a glass test tube into the neck. Prints as shown on its floor, no supports.
MAIN PURPOSE: Catch keys, rings and small trinkets
A low dish that swells out at the middle like a spun bowl, covered in a crisp diamond knurl that catches the light from every side. About 120 mm across and 30 mm tall, it's a neat catch-all for keys, rings, coins, earbuds or a candle.
Prints in one piece with no supports. Change the size, the curve or the diamond size in the editor to make your own.
Printing notes
48.8 cm³
Volume
60.5 g
Est. weight
132,004
Triangles
Silk or matte PLA both show the diamonds well. 3 walls keep the knurl solid. Prints as shown on its floor, no supports.
A tall, slim vase that swells gently through the middle, covered all over in a diamond knurl like a cut-glass grip. 150 mm tall and about 80 mm across, so it suits a single stem, dried flowers or grasses, or pens, brushes and kitchen utensils.
Prints in one piece with no supports. Change the height, the diameter or the curve in the editor to make your own.
Printing notes
112.2 cm³
Volume
139.2 g
Est. weight
438,964
Triangles
Use 3 walls so the diamonds print solid. For fresh flowers in water, print in PETG or stand a glass inside. Prints as shown on its floor, no supports.
MAIN PURPOSE: Display dried flowers or a single stem
A small bottle vase with a round belly, a narrower neck and a gently flared lip, covered in a crisp diamond knurl. About 110 mm across and 100 mm tall, it reads like a classic cut-glass bottle.
Prints in one piece with no supports. Change the size, the belly or the neck in the editor to make your own.
Printing notes
112.8 cm³
Volume
139.9 g
Est. weight
430,500
Triangles
Silk or dual-colour PLA makes the diamonds sparkle. For fresh flowers in water, print in PETG or stand a glass inside. Prints as shown on its floor, no supports.
MAIN PURPOSE: Serve fruit and snacks, or hold keys
A wide, shallow bowl wrapped in a crisp diamond knurl, standing on three slim splayed legs. About 155 mm across with a low 25 mm bowl, it's ideal for fruit, snacks, keys or a candle on a table or shelf.
The legs print separately and press into holes under the bowl, so every part prints flat with no supports. Change the size or the diamond size in the editor to make your own.
Printing notes
86.1 cm³
Volume
106.7 g
Est. weight
40,028
Triangles
Print the three legs separately and press them into the holes underneath; a drop of glue makes them permanent. Prints as shown on its floor, no supports.
MAIN PURPOSE: Display a single stem or dried flowers
A tall gourd-shaped vase with a low round belly and a long slim neck that flares out at the lip, covered all over in a crisp diamond knurl. About 95 mm across and 150 mm tall, made for a single stem or a few dried flowers.
Prints in one piece with no supports. Change the height, the belly or the neck in the editor to make your own.
Printing notes
97.9 cm³
Volume
121.5 g
Est. weight
518,884
Triangles
Slow the print down for the slim neck, or print two at once, so each small layer can cool. For fresh flowers, print in PETG or slip a glass test tube into the neck. Prints as shown on its floor, no supports.
MAIN PURPOSE: Catch keys, rings and small trinkets
A low dish that swells out at the middle like a spun bowl, wrapped in a woven basket pattern that looks like rattan or wicker. About 115 mm across and 30 mm tall, it's a neat catch-all for keys, rings, coins, earbuds or a candle.
Prints in one piece with no supports. Change the size, the curve or the weave size in the editor to make your own.
Printing notes
46.6 cm³
Volume
57.8 g
Est. weight
92,836
Triangles
Wood-fill or matte tan PLA makes it look like real woven rattan. Prints as shown on its floor, no supports.
A tall, slim vase that swells gently through the middle, wrapped all over in a woven basket pattern like a wicker sleeve. 150 mm tall and about 75 mm across, so it suits a single stem, dried flowers or grasses, or pens, brushes and kitchen utensils.
Prints in one piece with no supports. Change the height, the diameter or the curve in the editor to make your own.
Printing notes
104.1 cm³
Volume
129.0 g
Est. weight
331,300
Triangles
Wood-fill or matte PLA gives a natural wicker look. For fresh flowers in water, print in PETG or stand a glass inside. Prints as shown on its floor, no supports.
MAIN PURPOSE: Display dried flowers or a single stem
A small bottle vase with a round belly, a narrower neck and a gently flared lip, wrapped in a woven basket pattern like a wicker-covered bottle. About 105 mm across and 100 mm tall.
Prints in one piece with no supports. Change the size, the belly or the neck in the editor to make your own.
Printing notes
105.6 cm³
Volume
130.9 g
Est. weight
303,780
Triangles
Wood-fill or matte tan PLA makes the weave look like real rattan. For fresh flowers in water, print in PETG or stand a glass inside. Prints as shown on its floor, no supports.
MAIN PURPOSE: Serve fruit and snacks, or hold keys
A wide, shallow bowl wrapped in a woven basket pattern, standing on three slim splayed legs, like a little wicker fruit bowl. About 150 mm across with a low 25 mm bowl, it's ideal for fruit, snacks, keys or a candle on a table or shelf.
The legs print separately and press into holes under the bowl, so every part prints flat with no supports. Change the size or the weave size in the editor to make your own.
Printing notes
83.8 cm³
Volume
104.0 g
Est. weight
28,508
Triangles
Print the three legs separately and press them into the holes underneath; a drop of glue makes them permanent. Prints as shown on its floor, no supports.
MAIN PURPOSE: Display a single stem or dried flowers
A tall gourd-shaped vase with a low round belly and a long slim neck that flares out at the lip, wrapped all over in a woven basket pattern like a wicker-covered demijohn. About 90 mm across and 150 mm tall, made for a single stem or a few dried flowers.
Prints in one piece with no supports. Change the height, the belly or the neck in the editor to make your own.
Printing notes
90.5 cm³
Volume
112.2 g
Est. weight
398,212
Triangles
Slow the print down for the slim neck, or print two at once, so each small layer can cool. Wood-fill PLA gives a natural wicker look. Prints as shown on its floor, no supports.
MAIN PURPOSE: Catch keys, rings and small trinkets
A low dish wrapped in smooth, rounded flutes that spiral 45° around it, swelling out at the middle like a spun bowl. About 120 mm across and 30 mm tall, it's a neat catch-all for keys, rings, coins, earbuds or a candle.
Prints in one piece with no supports. Change the size, the flute depth or the twist in the editor to make your own.
Printing notes
91.8 cm³
Volume
113.9 g
Est. weight
54,496
Triangles
Silk PLA makes the rounded flutes shimmer as they turn; 3 walls keep the flutes solid. Prints as shown on its floor, no supports.
A tall, slim vase wrapped in smooth, rounded flutes that spiral 45° around it and swell gently through the middle. 150 mm tall and about 80 mm across the flutes, so it suits a single stem, dried flowers or grasses, or pens, brushes and kitchen utensils.
Prints in one piece with no supports. Change the height, the diameter, the flute depth or the twist in the editor to make your own.
Printing notes
232.7 cm³
Volume
288.5 g
Est. weight
81,544
Triangles
Use 3 walls so the flutes print solid. For fresh flowers in water, print in PETG or stand a glass inside. Prints as shown on its floor, no supports.
MAIN PURPOSE: Display dried flowers or a single stem
A small bottle vase with a round belly and a narrow neck, wrapped in smooth, rounded flutes that spiral 45° around it. The flutes are deepest at the belly and thin out towards the neck, like a classic bottle given a soft twist. About 110 mm across the flutes and 100 mm tall.
Prints in one piece with no supports. Change the size, the belly or the neck in the editor to make your own.
Printing notes
245.5 cm³
Volume
304.4 g
Est. weight
72,080
Triangles
Silk or dual-colour PLA makes the spiral stand out. For fresh flowers in water, print in PETG or stand a glass inside. Prints as shown on its floor, no supports.
MAIN PURPOSE: Serve fruit and snacks, or hold keys
A wide, shallow bowl wrapped in smooth, rounded flutes that spiral 45° around it and swell out at the middle, standing on three slim splayed legs. About 170 mm across the flutes with a low 25 mm bowl, it's ideal for fruit, snacks, keys or a candle on a table or shelf.
The legs print separately and press into holes under the bowl, so every part prints flat with no supports. Change the size, the flute depth or the twist in the editor to make your own.
Printing notes
139.6 cm³
Volume
173.1 g
Est. weight
135,532
Triangles
Print the three legs separately and press them into the holes underneath; a drop of glue makes them permanent. Prints as shown on its floor, no supports.
MAIN PURPOSE: Display a single stem or dried flowers
A tall gourd-shaped vase with a low round belly and a long slim neck that flares out at the lip, wrapped in smooth, rounded flutes that spiral 45° around it. The flutes are deepest at the belly and fade away up the neck. About 110 mm across the flutes and 150 mm tall, made for a single stem or a few dried flowers.
Prints in one piece with no supports. Change the height, the belly or the neck in the editor to make your own.
Printing notes
247.9 cm³
Volume
307.4 g
Est. weight
190,500
Triangles
Slow the print down for the slim neck, or print two at once, so each small layer can cool. For fresh flowers, print in PETG or slip a glass test tube into the neck. Prints as shown on its floor, no supports.
MAIN PURPOSE: Catch keys, rings and small trinkets
A low dish that swells out at the middle like a spun bowl, wrapped in neat stacked rings like a turned pot on a potter's wheel. About 120 mm across and 30 mm tall, it's a neat catch-all for keys, rings, coins, earbuds or a candle.
Prints in one piece with no supports. Change the size, the curve or the ring spacing in the editor to make your own.
Printing notes
57.8 cm³
Volume
71.6 g
Est. weight
79,298
Triangles
Matte or stone-effect PLA gives it a turned-ceramic look; 3 walls keep the rings solid. Prints as shown on its floor, no supports.
A tall, slim vase that swells gently through the middle, wrapped from top to bottom in stacked rings like a coiled clay pot. 150 mm tall and about 80 mm across, so it suits a single stem, dried flowers or grasses, or pens, brushes and kitchen utensils.
Prints in one piece with no supports. Change the height, the diameter or the ring spacing in the editor to make your own.
Printing notes
139.9 cm³
Volume
173.5 g
Est. weight
275,724
Triangles
Matte or stone-effect PLA gives a ceramic look. For fresh flowers in water, print in PETG or stand a glass inside. Prints as shown on its floor, no supports.
MAIN PURPOSE: Display dried flowers or a single stem
A small bottle vase with a round belly, a narrower neck and a gently flared lip, wrapped in stacked rings like a hand-coiled clay pot. About 110 mm across and 100 mm tall.
Prints in one piece with no supports. Change the size, the belly or the neck in the editor to make your own.
Printing notes
138.2 cm³
Volume
171.3 g
Est. weight
246,266
Triangles
Matte terracotta or stone-effect PLA makes it look like real pottery. For fresh flowers in water, print in PETG or stand a glass inside. Prints as shown on its floor, no supports.
MAIN PURPOSE: Serve fruit and snacks, or hold keys
A wide, shallow bowl wrapped in neat stacked rings, standing on three slim splayed legs. About 155 mm across with a low 25 mm bowl, it's ideal for fruit, snacks, keys or a candle on a table or shelf.
The legs print separately and press into holes under the bowl, so every part prints flat with no supports. Change the size or the ring spacing in the editor to make your own.
Printing notes
97.0 cm³
Volume
120.3 g
Est. weight
35,556
Triangles
Print the three legs separately and press them into the holes underneath; a drop of glue makes them permanent. Prints as shown on its floor, no supports.
